Expert answer:data and computer Communication

Solved by verified expert:I need some who can do this project
eegr410_fall2017_project3.pdf

Unformatted Attachment Preview

EEGR410: Introduction to Networks /Fall 2017
Project 3__
1. Project Description
The purpose of this project is to configure the network schematic as shown below in
Figure 1 using GNS3. The network consists of three buildings (Engineering, CBEIS and
Montebello) of Morgan State University. Each of the buildings has their own router,
switch and hosts. The configuration of the network is summarized in the table below.
Figure 1: Network Diagram using Microsoft Visio®
BUILDING
PC
Interface IP
ENGINEERING
10.1.1.1
Fa0/0: 10.1.1.251
255.255.255.0
S0/0: 10.1.128.251
gateway 10.1.1.251
S0/1: 10.1.130.251
10.1.3.1
Fa0/0: 10.1.3.253
255.255.255.0
S0/0: 10.1.130.253
gateway 10.1.3.253
S0/1: 10.1.129.253
10.1.2.1
Fa0/0: 10.1.2.252
255.255.255.0
S0/0: 10.1.128.252
gateway 10.1.2.252
S0/1: 10.1.129.252
CBEIS
MONTEBELLO
Table 1: IP Address Assignment
2. Configure the IP addresses of the hosts (make sure you are using VPCs as hosts in your
GNS3). You can configure the IP address of a host using the command
 VPCS # ip [address] [netmask] [gateway]
3. Configure the routers (Engineering, CEBIS and Montebello). Recommended routers
c3745.
Example: Configuration of the IP address of the Fast Ethernet interface of Router R.
 R# enable
 R# conf t
 R(config)# int f0/0
 R(config-if)#ip add [address] [netmask]
 R(config-if)#no sh
 R(config-if)#exit
 R(config)#end
 R#
Configuring a routing protocol on a router. For example for routing protocol eigrp
 R# conf t
 R(config)#router eigrp 100
 R(config)#network [network address] ….repeat this command for the total
number of networks the router is adjacent (connected with a serial interface)
 R(config)#no auto-summary
 R(config)#end
 R#
 R#copy running-config startup-config …copy running configuration to startup
configuration. This will help you save the running-config to startup-config .
N.B.: If you don’t have serial interfaces for connecting the routers to one another,
you can always add additional WIC interfaces by changing the configuration.
4. Check Connectivity by running the ping command
Ping PC1 from PC2
 Ping 10.1.1.1
You should be getting as an output if you are successful in configuring your network of
the form
Example: y bytes from 10.1.1.1 icmp_seq=2 ttl=62 time=29.590 ms
Explain the result of this command output
5. Check the output of the routers with commands
 Show ip route
 Show arp
Explain the output of both command outputs
6. Now ping PC1 from PC2, PC2 from PC3 and PC1 from PC3 and check the result of the
outputs.
 Show ip route
 Show arp
Explain the output of both command outputs difference from the result of step 5.
7. Determine the MAC addresses of the hosts.
8. Since the GNS3 Workbench has a Wireshark integrated, right click and capture on the
serial link between any of two routers. Save and analyze/explain the meaning of packets
exchanged?
9. Add an additional VPC host to the Montebello Switch (you can choose any of the
switches) and name the host with your first name as in Figure 2 (e.g. here I used in my
design my first name). To complete this task and verify this host is added to the network
successfully:
– Select a proper IP address, default gateway and subnet mask that this host can be
assigned.
-ping to the other hosts in the same network (Montebello building) verify its success.
-ping one of the hosts in a different sub network e.g. Engineering building and verify its
success.
Figure 3: Expected Final Network Design
10. Consider an application layer packet sent from PC1 to PC2. Describe the journey of the
packet in details as it traverses the routers and switches and to reach its destination. You
should be able to apply the concepts of encapsulation/ decapsulation as the packet
traverses the TCP/IP layer, packet processing and forwarding at routers and switches.
Deliverables:
-Your network topology diagram (gns3 file) in *.zip format. Don’t forget to save your running
configuration to start up configuration (if you don’t do so, you will lose all the
configurations during the next startup). You can also export and save them in your working
directory.
-a report showing the screen shots of each of the steps followed during configuration
accompanied by explanation.
-an explanation of the questions together with their corresponding screen shots and the screen
shot of the final Network diagram.
Note: your project report should be a single *.pdf file of the report and grading will take
into account project report theoretical explanation, format, clarity, originality, grammar
and a detail explanation of each of the procedures followed together with their screen shots
if there are any !
…
Purchase answer to see full
attachment

How it works

1. Paste your instructions in the instructions box. You can also attach an instructions file
2. Select the writer category, deadline, education level and review the instructions 
3. Make a payment for the order to be assignment to a writer
4.  Download the paper after the writer uploads it 

Will the writer plagiarize my essay?

You will get a plagiarism-free paper and you can get an originality report upon request.

Is this service safe?

All the personal information is confidential and we have 100% safe payment methods. We also guarantee good grades